A de Laval nozzle (or convergent-divergent nozzle, CD nozzle or con-di nozzle) is a tube that is pinched in the middle, making a carefully balanced, asymmetric hourglass-shape. It is used to accelerate a hot, pressurised gas passing through it to a supersonic speed, and upon expansion, to shape the exhaust flow so that the heat energy propelling the flow is maximally converted into directed kinetic energy. Because of this, the nozzle is widely used in some types of steam turbine, it is an essential part of the modern rocket engine, and it also sees use in supersonic jet engines.
This principle was used in a rocket engine by Robert Goddard and in very nearly all modern rocket engines that employ hot gas combustion use de Laval nozzles.
Its operation relies on the different properties of gases flowing at subsonic and supersonic speeds. The speed of a subsonic flow of gas will increase if the pipe carrying it narrows because the mass flow rate is constant. The gas flow through a de Laval nozzle is isentropic (gas entropy is nearly constant). At subsonic flow the gas is compressible; sound, a small pressure wave, will propagate through it. At the "throat", where the cross sectional area is a minimum, the gas velocity locally becomes sonic (Mach number = 1.0), a condition called choked flow. As the nozzle cross sectional area increases the gas begins to expand and the gas flow increases to supersonic velocities where a sound wave will not propagate backwards through the gas as viewed in the frame of reference of the nozzle (Mach number > 1.0).
Conditions for operationEdit
A de Laval nozzle will only choke at the throat if the pressure and mass flow through the nozzle is sufficient to reach sonic speeds, otherwise no supersonic flow is achieved and it will act as a Venturi tube.
In addition, the pressure of the gas at the exit of the expansion portion of the exhaust of a nozzle must not be too low. Because pressure cannot travel upstream through the supersonic flow, the exit pressure can be significantly below ambient pressure it exhausts into, but if it is too far below ambient, then the flow will cease to be supersonic, or the flow will separate within the expansion portion of the nozzle, forming an unstable jet that may 'flop' around within the nozzle, possibly damaging it.
In practice ambient pressure must be no higher than roughly 2-3 times the pressure in the supersonic gas at the exit for supersonic flow to leave the nozzle.
Analysis of gas flow in de Laval nozzlesEdit
The analysis of gas flow through de Laval nozzles involves a number of concepts and assumptions:
- For simplicity, the gas is assumed to be an ideal gas.
- The gas flow is isentropic (i.e., at constant entropy). As a result the flow is reversible (frictionless and no dissipative losses), and adiabatic (i.e., there is no heat gained or lost).
- The gas flow is constant (i.e., steady) during the period of the propellant burn.
- The gas flow is along a straight line from gas inlet to exhaust gas exit (i.e., along the nozzle's axis of symmetry)
- The gas flow behavior is compressible since the flow is at very high velocities.
Exhaust gas velocityEdit
As the gas enters a nozzle, it is traveling at subsonic velocities. As the throat contracts down the gas is forced to accelerate until at the nozzle throat, where the cross-sectional area is the smallest, the linear velocity becomes sonic. From the throat the cross-sectional area then increases, the gas expands and the linear velocity becomes progressively more supersonic.
|Ve||= Exhaust velocity at nozzle exit, m/s|
|T||= absolute temperature of inlet gas, K|
|R||= Universal gas law constant = 8314.5 J/(kmol·K)|
|M||= the gas molecular mass, kg/kmol (also known as the molecular weight)|
|k||= cp/cv = isentropic expansion factor|
|cp||= specific heat of the gas at constant pressure|
|cv||= specific heat of the gas at constant volume|
|Pe||= absolute pressure of exhaust gas at nozzle exit, Pa|
|P||= absolute pressure of inlet gas, Pa|
Some typical values of the exhaust gas velocity Ve for rocket engines burning various propellants are:
- 1700 to 2900 m/s (3,800 to 6,500 mph) for liquid monopropellants
- 2900 to 4500 m/s (6,500 to 10,100 mph) for liquid bipropellants
- 2100 to 3200 m/s (4,700 to 7,200 mph) for solid propellants
As a note of interest, Ve is sometimes referred to as the ideal exhaust gas velocity because it based on the assumption that the exhaust gas behaves as an ideal gas.
As an example calculation using the above equation, assume that the propellant combustion gases are: at an absolute pressure entering the nozzle of P = 7.0 MPa and exit the rocket exhaust at an absolute pressure of Pe = 0.1 MPa; at an absolute temperature of T = 3500 K; with an isentropic expansion factor of k = 1.22 and a molar mass of M = 22 kg/kmol. Using those values in the above equation yields an exhaust velocity Ve = 2802 m/s or 2.80 km/s which is consistent with above typical values.
The technical literature can be very confusing because many authors fail to explain whether they are using the universal gas law constant R which applies to any ideal gas or whether they are using the gas law constant Rs which only applies to a specific individual gas. The relationship between the two constants is Rs = R/M.
For example a de Laval nozzle using hot air at a pressure of 1,000 psi (6.9 MPa or 68 atm), temperature of 1470 K, would have a pressure of 540 psi (3.7 MPa or 37 atm), temperature of 1269 K at the throat, and 15 psi (0.1 MPa or 1 atm), temperature of 502 K at the nozzle exit. The expansion ratio, nozzle cross sectional area at exit divided by area at throat, would be 6.8. The specific impulse would be 151 s (1480 N·s/kg).
Application to celestial objects Edit
Theoretical astrophysicists have found that pipes with the flow pattern of a De Laval nozzle have analogous phenomena in the interstellar medium. The interior of an accretion disk has a similar function as the pipe, save it is not a solid wall, but itself a fluid that can contain a relativistic jet by a pressure balanced boundary.
- Spacecraft propulsion
- Rocket engine
- Rocket engine nozzles
- Venturi tube
- Choked flow
- Twister Supersonic Separator for natural gas treatment
- Active galactic nucleus
- History of the internal combustion engine
- ↑ See: British patent 7143 of 1889.
- ↑ (1) Theodore Stevens and Henry M. Hobart, Steam Turbine Engineering (New York, N.Y., The MacMillan Co., 1906), pages 24-27.(Available on-line at: http://books.google.com/books?id=9ElMAAAAMAAJ&pg=PA27&lpg=PA26&ots=i9N3YYNjIF&ie=ISO-8859-1&output=html ) ; (2) Robert M. Neilson, The Steam Turbine (London, England: Longmans, Green, and Co., 1903), pages 102-103. (Available on-line at: http://books.google.com/books?id=ODhMAAAAMAAJ&pg=PA102&lpg=PA102&ots=WYaRaosiiM&ie=ISO-8859-1&output=html ) ; (3) Garrett Scaife, From Galaxies to Turbines: Science, Technology, and the Parsons Family (Abingdon, England: Taylor & Francis Group, LLC: 2000), page 197. (Available on-line at: http://books.google.com/books?id=BeMjgxsifcQC&pg=PA197&lpg=PA197&source=bl&ots=VpRffcaLG2&sig=mNb8dGDFErN8mgmo79HN6Dpa2DM&hl=en&ei=jMkjS82WFJHIlAew4IH9CQ&sa=X&oi=book_result&ct=result&resnum=10&ved=0CCUQ6AEwCTgU ) ; (4) John David Anderson, Modern Compressible Flow: With Historical Perspective, 3rd ed. (New York, New York: McGraw-Hill, 2003), page 229. (Available on-line at: http://books.google.com/books?id=woeqa4-a5EgC&pg=PA229&lpg=PA230&ots=bwerpi2LWc&ie=ISO-8859-1&output=html ).
- ^ Clarke, C. J. & Carswell B. (2007). Principles of Astrophysical Fluid Dynamics, chpt 9.2 (1st Edition ed.), Cambridge University Press. pp. 226. ISBN 978-0521853316.
- ^ Richard Nakka's Equation 12
- ^ Robert Braeuning's Equation 2.22
- ^ Sutton, George P. (1992). Rocket Propulsion Elements: An Introduction to the Engineering of Rockets (6th Edition ed.), Wiley-Interscience. pp. 636. ISBN 0471529389. cs:Lavalova dýzahr:De Lavalova mlaznica